|
Competition, Action Shooting And Training. Competition, Three gun, IPSC, IDPA , and Training discussion here. |
|
Thread Tools | Display Modes |
#3
|
|||
|
|||
The reason for the notches, was too keep them together without being permanent so I could break down for storage. Then bought too if Velcro and stapled to bottom board for your down. Not pretty but did the job.
Sent from my SM-N960U using Tapatalk |
#4
|
|||
|
|||
One other thing I did. First one was too tight for the center board holding steel Target to get in. So I bought large washers and put one on each side of the little 2x4 blocks screwed in. This made enough space to slide the standing center 2x4 in.
Sent from my SM-N960U using Tapatalk |
#6
|
|||
|
|||
I have been using 3/4" pvc frmes and have similar 2x4 set up target butts. asy to break down and pvc cheap. Same as used at angeles shooting ranges. 2' center to center.
|
#7
|
||||
|
||||
Nice OP. I made some as well but mine don't break down. Like yours. Gonna change to your design.
Quote:
Sent from my SM-G930U using Tapatalk |
#9
|
|||
|
|||
I made some with larger 2"? pvc and filled the bottom with sand and gravel for weight. Screwed pipe and fittings together. But i have 5 steel stands that use the standard 1x2s and in the center a 2x4 for steel. The stands have angle iron to protect them from an impact. They were about $35 each.
|
#10
|
|||
|
|||
I wanted a set of target stands,so I got a friend to teach me how to weld.
I made a simple target stand that worked out very well and I made a bunch for the gun club I belong to. I made 2 sizes, 18" and a 18-24" combo. The problem is that the "H" shaped stand takes up a lot of space in the small SUV that I drive. So the target stands I make now have to fold up and fit in a Honda CRV. Here's my stand for 18" IPSC targets. Here's a few more. The one on the left takes 2x4 lumber that I use for rifle targets and folds up. The other 2 I use for pistol steel or paper targets. Here's a pic of the rifle target stand broken down. I also made a static plate rack that comes apart, the longest piece is 55". Last edited by CamW; 06-14-2019 at 10:23 PM.. |
#12
|
|||
|
|||
A friend brought one of the MGM "plate rack in a bucket" to the range, it's pretty good design but the 2x4 cross piece didn't last very long, there were a bunch of new shooters that day.
That's why I made my rack out of steel. I only shoot pistol and bird shot at it. Last edited by CamW; 06-15-2019 at 9:16 AM.. |
#14
|
||||
|
||||
Nicely done...
__________________
"Extremism in defense of liberty is no vice. Moderation in pursuit of justice is no virtue." ----Sen. Barry Goldwater Those who would give up essential Liberty, to purchase a little temporary Safety, deserve neither Liberty nor Safety." ----Benjamin Franklin NRA life member CRPA member |
#15
|
||||
|
||||
Is Angeles and Hodge rd the only places near SGV where we can shoot at steel? I just started getting into welding a dueling tree but have yet to settle on where to shoot it
__________________
https://imgur.com/a/yO4kS |
#18
|
||||
|
||||
Jeez you really need to fertilize your lawn.
__________________
Some say that he once mooned two prostitutes just for a round of drinks, but wasn't surprised by the reply......They call him, the Hutch Some say that he rode a dirtbike 7k miles across the country and that he once applied Bengay to his own testicles for a mere $50............They call him, the Hutch -Top Gear http://media.liveauctiongroup.net/i/...CCAB7CE8D70F60 |
#19
|
||||
|
||||
i need to get working on my target stands too...
__________________
Quote:
Quote:
|
Thread Tools | |
Display Modes | |
|
|