|
Shotgun discussions Trap, Hunting, Defense and more. A place for enthusiasts to discuss the shotgun. |
|
Thread Tools | Display Modes |
#3
|
||||
|
||||
Not a Phillips run, but I did stop at the Reloading Store and picked up everything I need. It cost me about $12 more than it would have at Phillips, but I can dial in the machine and test some shells on Sunday.
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#5
|
||||
|
||||
True, but I woundn't drive down there unless I was already heading to BBB's any way.
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#8
|
||||
|
||||
Eagle Magnum shot was $47.
Primers were $30. That's the extra $12, powder was the same price. I only bought 1lb of powder, 25lbs of shot and 1000 primers. I want to make sure I like the load before I spend big bucks on supplies. The loading bench is ready to go...
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" Last edited by ceh383; 07-19-2018 at 7:01 PM.. |
#9
|
||||
|
||||
Very nice. Clean and functional.
__________________
********************* WTS: 1. PW 800+ Hydro Multispeed (just the hydraulic unit that also works with Spolar press) 2. PW 800B converted to 800C (12 gauge) with lots of accessories and upgrades 3. Hornady 366 (12 gauge) |
#10
|
||||
|
||||
Reclaimed is expensive down there. It is usually $1/lb up here.
Alternatively, the best deal I have found on new shot is $45.99/25lb bag.
__________________
********************* WTS: 1. PW 800+ Hydro Multispeed (just the hydraulic unit that also works with Spolar press) 2. PW 800B converted to 800C (12 gauge) with lots of accessories and upgrades 3. Hornady 366 (12 gauge) |
#11
|
||||
|
||||
Thanks, just need to add some mouldings to catch run-away shot and paint it and it will be final. But for right now it will get the job done
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#13
|
||||
|
||||
Thanks, no not this month, I'm going to M-N-M Sunday. Thinking about doing it next month, keep me in mind when you squad up
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#14
|
||||
|
||||
Amazing how prices vary from one place to another. At $1 per lb, I'd shoot a lot of reclaimed.
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#15
|
||||
|
||||
I use mec jr's, and the reclaimed seem to give me problems, mostly hanging up in the drop tube on 2 of my reloaders, if prices get bad, I may have to try it again
|
#16
|
||||
|
||||
First two off the press...
Need to fine tune the crimp...Tomorrow, I'm done for the night.
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#18
|
||||
|
||||
Not yet, Sunday...
The hulls just arrived today. Spent a couple hours setting up the primer feed, primer seating and measuring powder charges. Tomorrow I will adjust the crimp and run off 100 or so to test on Sunday.
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#19
|
||||
|
||||
Quote:
Cool. I’m brining a box of Cheddite hulls I loaded on Sunday too 8am ? Sent from my iPhone using Tapatalk |
#21
|
||||
|
||||
LW, you shooting at M-N-M or the Sansei at BBB's?
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
#22
|
||||
|
||||
I hope it shoots well. Shells look good
__________________
********************* WTS: 1. PW 800+ Hydro Multispeed (just the hydraulic unit that also works with Spolar press) 2. PW 800B converted to 800C (12 gauge) with lots of accessories and upgrades 3. Hornady 366 (12 gauge) |
#23
|
||||
|
||||
I’m planning to shoot M N M I’m going to a skeet clinic tomorrow. I want to do sansei next month though Sent from my iPhone using Tapatalk |
#24
|
||||
|
||||
Thanks, the crimps are a little off, I'll work on that tomorrow. I will test them out Sunday and report back, they should be fine, very close to the factory loads I currently shoot.
Quote:
See ya Sunday
__________________
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed" |
Thread Tools | |
Display Modes | |
|
|