|
Ammo and Reloading Factory Ammunition, Reloading, Components, Load Data and more. |
|
Thread Tools | Display Modes |
#282
|
||||
|
||||
My dad and I were seriously looking at getting the hydraulic kit for it some time down the road.
|
#283
|
||||
|
||||
__________________
Actually I only started collecting Milsurps 3 years ago. I think I might own about 24...They're cheaper than guns that will most likely never get the opportunity to kill somebody... I belong to the group that uses firearms, and knows which bathroom to use. Tis better to have Trolled & lost, Than to never have Trolled, at all. Secret Club Member?. |
#284
|
|||
|
|||
Added a little more to my bench and installed some cabinets....So many toys, so little time. Between Mountain biking, Dirt biking, Fly Fishing, Shooting, Reloading and being married with 2 kids, Life is rough......
|
#285
|
|||
|
|||
interested in a 100 and a 125 for the kids?
|
#288
|
||||
|
||||
[
__________________
Latigo and P An'' ole' Brer' Rabbit...... he set in de bushes..... he watch an' he wait... lay low an' he don' say nuffin'. www.swissproductsusa.com |
#289
|
||||
|
||||
Latigo wins
__________________
“While I've often said I wanted to die in bed, what I meant is in my old age I wanted to be stepped on by an elephant while making love.” ― Roger Zelazny, The Great Book of Amber |
#290
|
||||
|
||||
I don't know about that, but I forgot my sorting tray.
__________________
Latigo and P An'' ole' Brer' Rabbit...... he set in de bushes..... he watch an' he wait... lay low an' he don' say nuffin'. www.swissproductsusa.com |
#291
|
||||
|
||||
Custom? Curious if it is how you did it, been trying to figure out how to do one for my bench, have ideas just have not had time to try them out
|
#292
|
||||
|
||||
I've promised to make a few for the guys on the long range forum. It's been so busy here I've haven't yet made them, but probably in a few more weeks. I think the largest one we've made is for 500 rounds of .308 cases.
I don them on the shop CNC out of Sintra. Its an expanded PVC, weighs quite a bit so it's stable. This one is a 250 tray for 7.5x55, and they're spaced apart so it's easier for me to grab them. Most are very close together. These are a three grain spread by 1/10ths of a grain.
__________________
Latigo and P An'' ole' Brer' Rabbit...... he set in de bushes..... he watch an' he wait... lay low an' he don' say nuffin'. www.swissproductsusa.com |
#293
|
||||
|
||||
So your just using an end mill to drill the holes on the CNC?
|
#295
|
||||
|
||||
Yes, it's an end mill, but it's a carbide type that does a complete clean on the bottom. Our standard end mills always seem to leave a bit of material in the bottom that requires a second clean-out pass for small fibers. The bit we use for plastics that assures us of a single pass costs about twice as much as the shop bits we use for steel and aluminum Swiss Products. Sorta odd.
*And I forgot our old press. Best one in the joint*
__________________
Latigo and P An'' ole' Brer' Rabbit...... he set in de bushes..... he watch an' he wait... lay low an' he don' say nuffin'. www.swissproductsusa.com Last edited by Latigo; 05-17-2012 at 5:08 AM.. |
#296
|
||||
|
||||
“While I've often said I wanted to die in bed, what I meant is in my old age I wanted to be stepped on by an elephant while making love.”
I'm having a hard time visualizing this. I assume that the elephant is on top?
__________________
Latigo and P An'' ole' Brer' Rabbit...... he set in de bushes..... he watch an' he wait... lay low an' he don' say nuffin'. www.swissproductsusa.com |
#299
|
||||
|
||||
Make it bigger. No matter how big you make it, it always ends up too small.
We're doubling the size this summer.
__________________
Latigo and P An'' ole' Brer' Rabbit...... he set in de bushes..... he watch an' he wait... lay low an' he don' say nuffin'. www.swissproductsusa.com |
#300
|
||||
|
||||
You might want to quit while only HALF of CalGuns hates you!
__________________
Quote:
|
Thread Tools | |
Display Modes | |
|
|