Pictures of Your Reloading Setup

[iareConfusE]

I've gotten a lot of good ideas for organization for my very basic reloading bench from The High Road's reloading forum, and I didn't see a picture thread on CGN, so I figured I would start one.

So, pictures of your setup for ideas!

[Revoman]

Three SDB's on a steel plate that is in a large vise that can swivel for access to all three when needed. Small area of garage, but works for me.





Shotshell part.... the overhead rafters carry a hopper that holds 100# of shot because I got tired of lifting the bags to fill the bottles.

[Triple R Munitions]

sorry for the mess. this is one of the loading areas.

R

[sequoia_nomad]

My humble little setup:

[Oceanbob]

A 1050 athat runs .45 and a 550B that runs 10mm. My shop is a Sanctuary and it calms me to putter-around in it.

[chim-chim7]

Am I missing something here, where are your fire extinguishers guys? Should be right next to your reloading bench. Iareconfuse has one! Good job.

[bruce381]

Originally Posted by Oceanbob

A 1050 athat runs .45 and a 550B that runs 10mm. My shop is a Sanctuary and it calms me to putter-around in it.

I like the pistol racks were did you get them?

[Ape]

Bit of a mess in these pics
But here's part of my gun room/reloading room/gunsmithing room.

[yakmon]

[RaymondMillbrae]

Here are a few older pictures.

This is a custom-made reloading bench in my office. I also reload for shotshell. (Attached pictures shows home-cast Lyman 525-grain sabot slugs).

In Christ: Raymond

[G lock]

subscribed

[iareConfusE]

Honestly, this thread should be stickied. Seeing other people's pictures gives us some really good ideas to mimic and utilize.

[TakeFive]

Like the original poster, I have a minimum amount of space.

[XDRoX]

[brando]

Yes, please sticky - there's much to learn from other people's setups. I wish I had some pics of my setup when it was in it's prime, however it's all packed away now that I'm living in the Southern Hemisphere.

[wellerjohn]

Originally Posted by Triple R Munitions

sorry for the mess. this is one of the loading areas.

R

Man I'm drooling.....

[thrillhouse700]

Originally Posted by iareConfusE

I've gotten a lot of good ideas for organization for my very basic reloading bench from The High Road's reloading forum, and I didn't see a picture thread on CGN, so I figured I would start one.

So, pictures of your setup for ideas!

I was gunna ask why you have a gas line going to your compressor Some kinda awesome flame thrower air compressor....

[iareConfusE]

Originally Posted by thrillhouse700

I was gunna ask why you have a gas line going to your compressor Some kinda awesome flame thrower air compressor....

Hah, that would be sweet.

[WileyWilly]

I have a very limited space (100 square feet) to cram everything in.
I made a quick-change base for my press. There is a threaded plate mounted under the bench.



Tooling mounted on the pegboard

[SixPointEight]

All of you talking about a minimum of space....amateurs! Hows this for minimum space?

I have a lee turret press coming, so I'll mount it and get a pic up soon.

[Deadon]

Nice setups guys. Ill have to snap a pic or two of mine.

[sfonelson]

Here's mine:

[Deadon]

Heres mine. Now if I could just get this setup to work!

[pdq_wizzard]

here is my mess

[jwest]

Well, for a trip down memory lane regarding this - hope this isn't too much of a tangent for some of you:

[freonr22]

Originally Posted by Deadon

Heres mine. Now if I could just get this setup to work!

report back what they say tomorrow, when u talk to hornady.